Radio Shack Speaker 40 4093 User Guide

4/9C["+P/9CNN"5RGCMGT  
40-4093  
OWNER’S MANUAL — Please read before using this equipment.  
Your RadioShack 2-Way In-Wall Speaker  
system makes it easy to mount your speaker  
flush with the ceiling or wall, making it ideal  
for unobtrusive use in a surround-sound  
system. The frame and grille can also be  
painted to match the room’s decor.  
"+/2146#06"  
#
#
1
4
features a crossover, a 5 / -inch woofer for  
rich lows, and a 1-inch tweeter for crisp  
highs. The speaker can handle up to 80 watts  
of music power. The wing-type mounting  
If an icon appears at the end of a paragraph, go  
to the box on that page with the corresponding  
icon for pertinent information.  
— Warning  
— Important  
#
Rý  
± — Note  
. — Caution  
° — Hint  
+056#..#6+10  
24'2#4+0)"6*'".1%#6+10  
To mount your speaker, you need the  
following items (not supplied, available at  
your local RadioShack or online at  
RadioShack.com).  
24'2#4+0)"6*'"52'#-'4  
If you choose to paint the frame and grille,  
paint them and let them dry before you  
connect the speaker wire or mount the  
speaker.  
• drywall or keyhole saw  
• wire stripper  
To remove the grille for painting, insert a  
paper clip into one of the grille openings, then  
pull up. Or, you can carefully twist the plastic  
frame back and forth until the grille edge  
becomes exposed, then lift the grille to  
remove it.  
• Phillips screwdriver  
• pencil or marker  
• 18–20 gauge speaker wire  
1. Be sure the mounting surface is between  
3
1
8
4-  
/ inch and 1 / inch thick, with at least a  
4
3
2 / -inch clearance behind the mounting  
surface and no wall studs or other  
objects to block the back of the speaker.  
2. Remove the inner cardboard disc from  
the supplied template/paint mask and  
keep it for later. Use the outer portion as  
a template to mark the cutout hole size  
and location for mounting the speaker.  
Carefully remove the dust cloth from behind  
the grill and replace it after you are finished  
painting.±  
±"016'"±"  
Do not paint the speaker element. We  
recommend you spray-paint the grille so paint  
does not block the holes.  
You can also paint the frame to match your  
wall or ceiling. To prevent paint from entering  
the speaker, remove the grille and insert the  
supplied cardboard paint mask. After the  
paint is dry, remove the paint mask and  
replace the grille.  
Paint Mask  
3. Use a drywall or keyhole saw to cut the  
."%#76+10".  
Be sure not to cut into any existing wiring or  
hole..  
plumbing hidden behind the wall.  
%100'%6+0)"6*'"52'#-'4"9+4'5  
Your local RadioShack store sells a wide  
selection of speaker wire. We recommend  
you use wire that is color-coded or marked on  
one side to help you connect the wire  
correctly.  
2. Separate about 4 inches of speaker wire  
at each end.  
1
/4 inch  
±"016'5"±"  
Avoid routing the speaker wire near electrical  
wires.  
1. Route the speaker wire to the speaker  
from the receiver.±  
4 inches  
Do not nail or staple the speaker wire.  
© 2002 RadioShack Corporation.  
All Rights Reserved.  
RadioShack and RadioShack.com are trademarks  
used by RadioShack Corporation.  
 

RCA Cassette Player Mobile Video Cassette Player User Guide
RCA Convection Oven RMW1170 User Guide
Rheem Water Heater 22DV40S 36N User Guide
RIDGID Soldering Gun RT 175 196 User Guide
Samsung Computer Drive BN68 01416D 00 User Guide
Samsung Refrigerator RA18FH User Guide
Samsung Stereo System AH68 01145B User Guide
Sanus Systems Indoor Furnishings NFAV230 User Guide
Sanus Systems Indoor Furnishings VMCT User Guide
Scientific Atlanta DVD Player 4250HDC User Guide